Arctic Cat 2013 Wildcat Service Manual Download

Page: 134 / 196

131

WC002B

3. The meter must show battery voltage.



NOTE: If the meter shows no battery voltage, trou-

bleshoot the fuse, switch, or the main wiring harness.



NOTE: If the meter shows battery voltage, the main

wiring harness is good; proceed to test the switch/
component and the connector.

RESISTANCE (Switch Connector)



NOTE: The brake pedal must be depressed for this test.

1. Set the meter selector to the OHMS position.

2. Connect the red tester lead to one terminal; then con-

nect the black tester lead to the other terminal.

3. When the pedal is depressed, the meter must show less

than 1 ohm.



NOTE: If the meter shows more than 1 ohm of resis-

tance, replace the switch.

Engine Coolant

Temperature (ECT)

Sensor



NOTE: Preliminary checks may be performed on this

component using the diagnostic mode on the LCD
gauge (see EFI Diagnostic System in this section).

1. Connect the meter leads (selector in OHMS position)

to the sensor terminals.

2. Suspend the sensor and a thermometer in a container

of cooking oil; then heat the oil.



NOTE: Neither the sensor nor the thermometer

should be allowed to touch the bottom of the con-
tainer or inaccurate readings will occur. Use wire
holders to suspend the sensor and thermometer.

3. On the ECT sensor when the temperature reaches 40°

C (104° F), the meter should read approximately 1136

ohms.

4. On the ECT sensor when the temperature reaches

100° C (212° F), the meter should read approximately

155 ohms.

5. If the readings are not as indicated, the sensor must be

replaced.

6. Install the sensor and tighten securely.

7. Connect the leads.

Fan Motor



NOTE: Preliminary checks may be performed on this

component using the diagnostic mode on the LCD
gauge (see EFI Diagnostic System in this section).

RESISTANCE (Fan Motor Connector)

1. Set the meter selector to the OHMS position.

2. Connect the red tester lead to one motor lead; then

connect the black tester lead to the other motor lead.

PR183A

3. The meter must show less than 1 ohm.



NOTE: If the meter shows more than 1 ohm of resis-

tance, troubleshoot or replace the fan motor.



NOTE: To determine if the fan motor is good, con-

nect the red wire from the fan connector to a 12 volt
battery; then connect the black wire from the fan con-
nector to ground. The fan should operate.

Power Distribution

Module (PDM)

FUSES/RELAYS



NOTE: To access fuses and relays, compress the

locking tabs on either side of the PDM cover and lift off.

The fuses are located in a power distribution module under

the passenger’s seat. If there is any type of electrical sys-

tem failure, always check the fuses first.

! WARNING

Wear insulated gloves and safety glasses. Heated oil
can cause severe burns.

! WARNING

Care should be taken to keep clear of the fan blades.

Summary of Contents for 2013 Wildcat





































































































































































































Search results

Summary of Contents for 2013 Wildcat

Reviews:

Related manuals for 2013 Wildcat

Brands by name

Popular brands

Arctic Cat 2013 Wildcat, Service Manual

Search results

Summary of Contents for 2013 Wildcat

Reviews:

Related manuals for 2013 Wildcat

Brands by name

Popular brands