Aqualisa Rise digital Installation Manual Download Page 2

Rise

 Installation Guide  02

IMPORTANT INFORMATION

Safety information

This appliance can be used by children aged 

from 3 years and above and persons with 

reduced physical, sensory or mental capabilities 

or lack of experience and knowledge if they 

have been given supervision or instruction 

concerning use of the appliance in a safe way 

and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be 

made by children without supervision.
This product must be installed by a competent 

person in accordance with all relevant current 

local and national Water Supply Regulations.

ALL PRODUCTS REQUIRING AN ELECTRICAL 

CONNECTION MUST BE INSTALLED BY A 

QUALIFIED PERSON FOLLOWING THE 

LATEST REVISION OF THE ELECTRICAL 

WIRING REGULATIONS, BOTH NATIONAL 

AND LOCAL AND CERTIFIED TO CURRENT 

BUILDING REGULATIONS.

This system should be installed so that other 

taps or appliances operated elsewhere within 

the premises do not significantly affect the flow.
The Quartz Smart Valve

 must not be used with 

a hot water supply temperature of over 65ºC. If 

the maximum hot water temperature is likely to 

rise above 65ºC then a Thermostatic Blending 

Valve must be used.
The Quartz Smart Valve

 is supplied factory 

pre-set at maximum temperature of 45ºC.  

The maximum temperature is fully adjustable  

to suit site conditions. If adjusted, we 

recommend the outlet temperature is set  

to a MAXIMUM of 46ºC.
The Quartz Smart Valve

 must be installed in an 

accessible location for servicing and maintenance.
The Quartz Smart Valve

 must not be installed 

in situations where either the ambient 

temperature is likely to exceed 40ºC or where 

freezing may occur.

The controller must not be installed in situations 

where the ambient temperature is likely to fall 

below 5ºC or rise above 40ºC.
We do not recommend the use of a controller  

in steam therapy facilities.
This appliance must be earthed.

Cables must be protected by a suitably sized 

conduit or trunking to avoid risk of damage and 

to allow removal for service and maintenance 

purposes

Ensure that the conduit is run to avoid the 

controller fixing holes.
Surface mounted cables must also be protected 

by a suitable approved conduit, even in a loft, 

where there may be a risk of damage from vermin.
The power lead must only be replaced by the 

manufacturer or his accredited agent.
The controller is supplied from a safety low 

voltage source.
This product is suitable for domestic use only.
Aqualisa products are supplied complete with  

a 1 year guarantee that can be upgraded by 

registering the product with Aqualisa. 
See www.aqualisa.co.uk/guarantee for details.

Installation of the pumped Quartz Smart 

Valve

 (for gravity stored systems)

The pumped Quartz Smart Valve

 shower 

system is designed to operate up to a maximum 

static pressure of 100kPa ((1 bar)(10 metres 

head)(14.5psi)). Under no circumstances must 

the pumped Quartz Smart Valve

 be connected 

directly to the water main or in line with another 

booster pump.
The minimum actual capacity of the cold  

water storage cistern should be not less than 

225 litres (50 gallons). The capacity of the hot 

water cylinder must be capable of meeting 

anticipated demand.

Summary of Contents for Rise digital
































Reviews: