manualshive.com logo in svg

Aplex APC-3228, User Manual

Share
Download
Aplex APC-3228 User Manual Download Page 91

APC-3228 User Manual   

91

Chapter 5        Touch Screen Installation 

 
This chapter describes how to install drivers and other software that will allow your PenMount 6000 
Controller Board to work with different operating systems. 

NOTE:

  PenMount USB drivers support up to 15 USB controllers. 

5.1 Introduction to Touch Screen Controller Board 

PenMount 6300 USB control board is a touch screen control board designed for USB interface and 
specific for 4, 5, 8-wire touch screens. It is designed with USB interface features with multiple devices 
supporting function. PenMount 6300 control board using PenMount 6000 controller that has been 
designed for those who may like and all-in-one solution with 10-bit A/D converter built-in to make the 
total printed circuit board denser, circuit diagram also designed for 12-bit ADC for optional. There are 
two connectors on this board, one connector is for 4, 5, 8-wire touch screen cable (optional), and 
another is for 4-pin USB A type cable (optional). 
 

 

Figure 5.1: Bird’s Eye View of Control Board 

 

 

 

5.2 Windows 2000/XP/2003/Vista Universal Driver Installation 

for PenMount 6000 Series 

Before installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system 
installed and running on your computer. You must also have one of the following PenMount 6000 
series controller or control boards installed: PM6500, PM6300. 
 
 
 

Summary of Contents for APC-3228











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands