manualshive.com logo in svg

Aplex APC-3228, User Manual

Share
Download
Aplex APC-3228 User Manual Download Page 17

APC-3228 User Manual   

17

2.2.3 Installing the Jumpers 
 

 

Clear CMOS (CLRTC1) 

This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS 
memory of date, time, and system setup parameters by erasing the CMOS RTC   
RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system 
setup information such as system passwords. To erase the RTC RAM: 
1.  Turn OFF the computer and unplug the power cord. 
2.  Remove the onboard battery. 
3.  Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 

seconds, then move the cap back to pins 1-2. 

4.  Re-install the battery. 
5.  Plug the power cord and turn ON the computer. 
6.  Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. 
 

 

Except when clearing the CMOS, never remove the cap on CLRTC 
jumper default position. Removing the cap will cause system boot 
failure!

 

 

 

Normal (Default) 

 

 

Clear RTC 

 

 
 

Summary of Contents for APC-3228











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands