Aplex APC-3228 User Manual Download Page 23 | Manualshive

Page: 23 / 106

background image

APC-3228 User Manual

23

CPU Fan Connector (CPU_FAN1)



Do not forget to connect the fan cables to the fan connectors.

Insufficient air flow inside the system may damage the
motherboard components, and hardware monitoring errors can
occur if you fail to plug this connector.



These are not jumpers! DO NOT place jumper caps on the fan

connectors.

System Fan Connector (SYS_FAN1)



Do not forget to connect the fan cables to the fan connectors.

Insufficient air flow inside the system may damage the
motherboard components, and hardware monitoring errors can
occur if you fail to plug this connector.



These are not jumpers! DO NOT place jumper caps on the fan

connectors.

«
...
21
22
23
24
25
...
»

Summary of Contents for APC-3228











































































































Reviews:

No comments

Related manuals for APC-3228

Brand: UMA Solar Pages: 35

Brand: IEI Technology Pages: 142

Brand: LG Pages: 27

Brand: LG Pages: 21

Brand: LG Pages: 18

ST-55-UHD-AND-L-004

Brand: Speechi Pages: 18

Brand: SOVA SOLAR Pages: 9

Brand: Aaeon Pages: 107

Brand: Van Der Valk Pages: 24

Brand: Xinje Pages: 41

Brand: Zennio Pages: 94

Brand: Ganz Pages: 10

Brand: Quanmax Pages: 14

SUNFRAME - INSTALLATION 80I.I

Brand: UNIRAC Pages: 12

Brand: IEI Technology Pages: 108

InteliVision 13Touch

Brand: ComAp Pages: 28

PPC-5008T-LX800

Brand: EBN Technology Pages: 53

Brand: Dell Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands