Aplex APC-3228 User Manual Download Page 103

Page: 103 / 106

APC-3228 User Manual

103

3. Touch each screen as it displays

“Please touch this monitor. Press ‘S’ to skip”

Following this

sequence and touching each screen is called

mapping the touch screens

4. After the setting procedure is finished, maybe you need to calibrate for each panel and controller

NOTES:

1. If you used a single VGA output for multiple monitors, please do not use the

Multiple Monitors

function. Just follow the regular procedure for calibration on each of your desktop monitors.

2. The Rotating function is disabled if you use the Multiple Monitors function.

3. If you change the resolution of display or screen address, you have to redo

Map Touch Screens

the system understands where the displays are.

4. If you more monitor mapping one touch screen,

Please press ‘S’ to skip mapping step.

Summary of Contents for APC-3228











































































































Search results

Summary of Contents for APC-3228

Reviews:

Related manuals for APC-3228

Brands by name

Popular brands

Aplex APC-3228, User Manual

Search results

Summary of Contents for APC-3228

Reviews:

Related manuals for APC-3228

Brands by name

Popular brands