manualshive.com logo in svg

Aplex APC-3228, User Manual

Share
Download
Aplex APC-3228 User Manual Download Page 60

APC-3228 User Manual   

60

  Change Supervisor Password 

The Security Setup screen is shown below. The sub menus are documented on the following pages. 

 

Change Supervisor Password 

This item indicates whether a supervisor password has been set. If the password has been installed, 

Installed 

displays. If not, 

Not Installed 

displays. 

Change User Password 

This item indicates whether a user password has been set. If the password has been installed, 

Installed 

displays. If not, 

Not Installed 

displays. 

3.7 Chipset Setup 

Select the 

Chipset 

tab from the setup screen to enter the Chipset BIOS Setup screen. You can select 

any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for 
that item. You can display a Chipset BIOS Setup option by highlighting it using the <Arrow> keys. All 
Chipset BIOS Setup options are described in this section. The Chipset BIOS Setup screen is shown 
below. 

Summary of Contents for APC-3228











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands