manualshive.com logo in svg

Aplex APC-3228, User Manual

Share
Download
Aplex APC-3228 User Manual Download Page 50

APC-3228 User Manual   

50

Intel AMT Configuration 

You can use this screen to select options for Intel AMT settings. Use the up and down <Arrow> keys 
to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. The 
settings are described on the following pages.   

 

 

Intel AMT Support 

Intel Active Management Technology (AMT) is hardware-based technology for 
remotely managing and securing PCs out-of-band. The options are Disabled, Enabled 

 

Force IDE/Force SOL 

SOL/ IDER (Serial Over LAN/ IDE-Redirection) is a protocol defined for Intel 
Active Management Technology that allows redirecting the keyboard/text or 
floppy disk/CD transfers from a local host to a remote workstation.   

 

Unconfigure AMT/ME 

To finish the unconfiguration of AMT, set this setting to [Enabled] and the BIOS 
will unconfigure all of AMT/ME settings and all the passwords are reset. 

Summary of Contents for APC-3228











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands