Aplex APC-3228 User Manual Download Page 2

Page: 2 / 106

APC-3228 User Manual

Warning!___________________________________

This equipment generates, uses and can radiate radio frequency energy and if not installed and

used in accordance with the instructions manual, it may cause interference to radio communications.

It has been tested and found to comply with the limits for a Class A computing device pursuant to

FCC Rules, which are designed to provide reasonable protection against such interference when

operated in a commercial environment. Operation of this equipment in a residential area is likely

to cause interference in which case the user at his own expense will be required to take whatever

measures may be required to correct the interference.

Disclaimer

This information in this document is subject to change without notice. In no event shall Aplex Technology

Inc. be liable for damages of any kind, whether incidental or consequential, arising from either the use or

misuse of information in this document or in any related materials.

Electric Shock Hazard – Do not operate the machine with its back cover removed. There are

dangerous high voltages inside.

Summary of Contents for APC-3228











































































































Search results

Summary of Contents for APC-3228

Reviews:

Related manuals for APC-3228

Brands by name

Popular brands

Aplex APC-3228, User Manual

Search results

Summary of Contents for APC-3228

Reviews:

Related manuals for APC-3228

Brands by name

Popular brands