manualshive.com logo in svg

Aplex APC-3228, User Manual

Share
Download
Aplex APC-3228 User Manual Download Page 37

APC-3228 User Manual   

37

 

 

Primary/Secondary IDE Master/Slave, Third/Fourth IDE Master, Fifth IDE Master/Slave 

Select one of the hard disk drives to configure it. Press <Enter> to access its the sub menu. The 
options on the sub menu are described in the following sections. 

 

 

IDE Detect Time Out (Sec) 

Set this option to stop the AMIBIOS from searching for IDE devices within the specified number of 
seconds. Basically, this allows you to fine-tune the settings to allow for faster boot times. Adjust this 
setting until a suitable timing that can detect all IDE disk drives attached is found. 
The default setting is 

35

. 

Option Description 

0 

This value is the best setting to use if the onboard IDE controllers are set to a 
specific IDE disk drive in the AMIBIOS. 

5 

Set this value to stop the AMIBIOS from searching the IDE bus for IDE disk 
drives in five seconds. A large majority of ultra ATA hard disk drives can be 
detected well within five seconds. 

10 

Set this value to stop the AMIBIOS from searching the IDE bus for IDE disk 
drives in 10 seconds. 

15 

Set this value to stop the AMIBIOS from searching the IDE bus for IDE disk 
drives in 15 seconds. 

20 

Set this value to stop the AMIBIOS from searching the IDE bus for IDE disk 
drives in 20 seconds. 

25 

Set this value to stop the AMIBIOS from searching the IDE bus for IDE disk 
drives in 25 seconds. 

30 

Set this value to stop the AMIBIOS from searching the IDE bus for IDE disk 
drives in 30 seconds. 

35 

35 is the default value. It is the recommended setting when all IDE connectors 
are set to AUTO in the AMIBIOS setting. 

Note: 

Different IDE disk drives take longer for the BIOS to locate than others do. 

Summary of Contents for APC-3228











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands