background image

- 14 -

15. Icons and Functions

Calibrated points

 

 

Self-Diagnosis 

Symbol

Er1, Er2, Er3, Er4, Er5, Er6

Stable reading 

indicator

   

Waterproof Rating

IP67, floats on water

Reading Lock

HOLD

Power

DC3V, AAA batteries*4

Bluetooth Signal

   

Battery Life

200 Hours

Low power reminder

Backlight

White: Measurement   

Green: Calibration   Red: Alarm

Auto. Power Off

Automatically power off if no operation for 10 minutes

Dimension/Weight

Instrument

40×40×178mm/133g;   case

255×210×50mm/680g;

16. Probe Replacement

To replace a probe:
1) Take off the probe cap; 2) Screw off the probe ring 3) Unplug the probe;
4) Plug in the new replacement probe (pay attention to the probe’s position); 
5) Screw on the probe ring tightly. Soak the probe in 3M KCL for 5-15 
minutes. Then perform calibration before testing. 

The replacement probes that are compatible with PC60-Z:

 

Ը

PC60-DE (Default pH/conductivity probe), PH60-DE (Regular pH probe for water solutions), 

 

Ը

PH60S-DE (spear pH probe for food testing), PH60F-DE (flat pH probe for surface testing)

 

Ը

EC60-DE (conductivity probe)

 

Ը

ORP60-DA (ORP probe).

*Probes don’t last forever. Every probe will eventually age and fail even if you don't use it that often. 
The typical service life of Apera probes is 12-24 months depending on the frequency of usage and 
how well you keep it clean and properly stored. We recommend replacing your probe every 1 to 2 
years to ensure the best performance.

Graph-3

LCD Display

Graph-4

pH calibration reminder

Graph-5

pH alarm triggered

Summary of Contents for ZenTest PC60-Z

















Reviews: