anvajo fluidlab R-300 User Manual Download Page 17 | Manualshive

Page: 17 / 69

anvajo fluidlab R-300 User Manual Download Page 17

User Manual fluidlab R-300

18

Edition 202104

Vers.: 1.2

4.

Plug the other end of the USB cable into the USB-C socket on the

fluidlab

R-

300 (Figure 2-1).

5.

The charging process is active when the power on/off button (Figure 2-2) on
the

fluidlab

R-300 lights up at regular intervals.

6.

The battery is fully charged when the power on/off button stops lighting up at
regular intervals or when the battery icon on the display is full.

7.

Disconnect the USB charger from the device when the battery is fully charged.
First unplug the connector on the USB cable from the device before
unplugging the power supply unit from the mains socket.

Note:

The

fluidlab

R-300 can be switched on and used for measurements during the

charging process.

It is not necessary to wait until the battery is fully charged before

switching the device on.

4.2

Switching On the Device

Note:

In order to be able to switch on the

fluidlab

R-300, either the device battery must

be charged (partially or fully) or the USB charger must be connected to the device
with the USB cable (see Chapter 4.1).

1.

Switch the unit on by pressing and holding down the power on/off button
(Figure 2-2) for approx. one second and then releasing it. The device is
switched on as soon as the power on/off button lights up.

2.

Wait until the system has started. This process takes approx. 40 seconds.
Start-up is complete when the main menu appears on the display. The device
is now ready for operation.

4.3

Switching Off the Device

Note:

There are several possible ways of switching off the

fluidlab

R-300.

For fault-free

operation of the

fluidlab

R-

300, you should use a “normal shutdown” whenever

possible. If a “normal shutdown” is not possible (e.g. as a result of a non

-responsive

system),

please select “error shutdown”.

Normal shutdown (recommended):

1.

Press and hold down the power on/off button (Figure 2-2) on the

fluidlab

R-

300 for approx. one second until a selection menu (“Shut down the device –

Yes/No”) appears on the display. Then immediately release the power on/off

button.

2.

Tap “Yes” to switch off the device. If you tap “No”, the process is cancelled,

and the device will remain switched on.

Error shutdown:

Warning!

Only perform this procedure if a “normal shutdown” (see above) is not possible.

«
...
15
16
17
18
19
...
»

Summary of Contents for fluidlab R-300






































































Reviews:

No comments