Anritsu 37 C Series, Operation Manual

Page: 73 / 603

37XXXC OM 4-23
FRONT PANEL OPERATION MEASUREMENT KEY-GROUP
MENU SU8 or CAL_SU8
PREVIOUS MENU
CALIBRATE FOR
FLAT PORT POWER
FORWARD
DIRECTION ONLY
XXX POINTS
MEASURE 1 PWR
POINT EVER
XX POINTS
POWER TARGET
-XXX.X dBm
START FLAT
POWER CALIBRATION
PRESS <ENTER>
TO SELECT
MENU DF1
DISCRETE FILL
INPUT START,
INCR, POINTS,
THEN SELECT
"FILL RANGE"
START FREQ
XX.XXXX GHz
INCREMENT
X.XXXX GHz
NUMBER OF PTS
XXX POINTS
STOP FREQ
XX.XXXX
FILL RANGE
(XXX ENTERED)
INDIVIDUAL
FREQ INSERT
CLEAR ALL
FINISHED
RETURN TO SWP
Measurement
Data
Points
Hold Domain
Setup
Menu
See
Chapter 9
Menu SU1
(Destroys Calibration)
PRESS <ENTER>
TO SELECT
OR TURN ON/OFF
MENU DF2
NEXT FREQ
XX.XXXX GHz
INSERT
INDIVIDUAL
FREQUENCIES
INPUT A FREQ,
PRESS <ENTER>
TO INSERT
XXX FREQS
ENTERED
LAST FREQ WAS
XX.XXXX GHz
AUTO INCR ON (OFF)
XX.XXXX GHz
PREVIOUS MENU
MENU SU9
PRESS <ENTER>
TO SELECT
NUMBER OF
DATA POINTS
1601 MAX PTS
801 MAX PTS
401 MAX PTS
201 MAX PTS
101 MAX PTS
51
MAX PTS
MENU SU9A
NUMBER OF
DATA POINTS
POINTS DRAWN
IN CW
XXXX POINT(S)
MENU SU3
SINGLE POINT
MEASUREMENT
SETUP
C.W. FREQ
XXX.XXXXXXXXX GHz
HOLD BUTTON
FUNCTION
TEST
SIGNALS
RETURN TO
SWEEP MODE
PRESS <ENTER>
TO SELECT
MENU SU5
FREQUENCY
MARKER SWEEP
START SWEEP
MARKER (n)
XXX.XXXXXXXXX GHz
STOP SWEEP
MARKER (n)
XXX.XXXXXXXXX GHz
USE KEYPAD
TO SELECT
MARKER (1-6)
MENU SU6
FREQUENCY
MARKER C.W.
C.W FREQ
MARKER (n)
XXXX.XXXXXXXXX GHz
USE KEYPAD
TO SELECT
MARKER (1-6)
MENU SU1
SWEEP SETUP
MARKER SWEEP
DISCRETE FILL
START
XX.XXXXXX GHz
STOP
XX.XXXXXX Gz
XXX DATA POINT(S)
XX.XXXXXXXXX GHz
STEP SIZE
C.W. MODE ON (OFF)
XX.XXXXXXXXX GHZ
HOLD BUTTON
FUNCTION
TEST SIGNALS
PRESS <ENTER>
TO SELECT
OR TURN ON/OFF
SET CENTER/SPAN
SWEEP SETUP
CENTER
XXX.XXXXXXXXX GHz
SPAN
XXX.XXXXXXXXX GHz
SET START/STOP
C.W. MODE ON (OFF)
XX.XXXXXXXXX GHZ
XXX DATA POINT(S)
XX.XXXXXXXXX GHz
STEP SIZE
MARKER SWEEP
DISCRETE FILL
HOLD BUTTON
FUNCTION
TEST SIGNALS
PRESS <ENTER>
TO SELECT
OR TURN ON/OFF
MENU SU1_CENTER
MENU SU4
HOLD/CONTINUE
HOLD/RESTART
SELECT FUNCTION
FOR
HOLD BUTTON
SINGLE SWEEP
AND HOLD
BIAS/RF HOLD
CONDITIONS
PRESS <ENTER>
TO SELECT
BIAS ON
RF ON
DUT/AUT ON (OFF)
PROTECTION
DEFAULT RESET
TURNS ON HOLD
WITH BIAS/RF
TURNED OFF
PRESS <ENTER>
TO SELECT
TURN KNOB TO
CHANGE NUMBER
OF POINTS
Appl
MENU SU3A
SWEPT POWER
SETUP
RETURN TO SWEPT
FREQUENCY MODE
P START
-XX.XX dBm
POWER SWEEP ON(OFF)
-XX.XX dB
HOLD BUTTON
FUNCTION
PRESS <ENTER>
TO SELECT
OR TURN ON/OFF
STEPSIZE
X.XX dB
SWEPT POWER
FREQUENCY
XXX.XXXXXXXXX GHz
P STOP
-XX.XX dBm
SWEPT POWER
GAIN COMPRESSION
To Menu
GC 4
See
Sheet 2
MENU SU2A
TEST SIGNALS
SOURCE 1 PWR
-XX.XX dBM
PORT 1 ATTN
0 *10 dB (0 - 70)
PORT 2 ATTN
0*10 dB (0-00)
PRESS <ENTER>
TO SELECT
OR TURN ON/OFF
.
MENU SU2, SU2a, CAL_SU2
TEST SIGNALS
POWER CONTROL
XX.X dB
(0 TO -15 dB)
SOURCE 2 PWR
XX.X dBm
PORT 1 POWER
-XX.XX dBm
PORT 2 ATTN
XXX dB (0-X0)
PRESS <ENTER>
TO SELECT
CALIBRATE
FOR FLATNESS
(CAL EXISTS)
FLATNESS ON(OFF)
CORRECTION
AT XX.X dBm
PORT 1 ATTN
20 dB (0 - 70)
EXIT APPLICATION*
SOURCE 2 PWR
-XX.XX dBM
To Menu
SU1
*Exit Application appears only
when in the Swept Frequency
Gain Compression application
Figure 4-7. Measurement Key-Group Menus Menu Flow (Sheet 1 of 2)