annke DN41R User Manual Download Page 36

Page: 36 / 106

Digital Video Recorder User Manual

Chapter 5 Recording Settings

5.1 Configuring Encoding Parameters

Before you start:

Make sure that the HDD has already been installed. If not, please install a HDD and initialize it.

(Menu>HDD>General)

Figure 5. 1 HDD- General

Click

Advanced

to check the storage mode of the HDD.

1) Whether the HDD mode is

Quota

, please set the maximum record capacity. For detailed information, see

Chapter 12.4 Configuring Quota Mode

2) If the HDD mode is

Group

, you should set the HDD group. For detailed information, see

Chapter 5.9

Configuring HDD Group for Recording

Figure 5. 2 HDD- Advanced

Steps

Enter the Record settings interface to configure the encoding parameters:

Menu>Record>Parameters

Figure 5. 3 Record Parameters

Set the parameters for recording.

1) Select the

Record

tab to configure.

Summary of Contents for DN41R











































































































Search results

Summary of Contents for DN41R

Reviews:

Related manuals for DN41R

Brands by name

Popular brands

annke DN41R, User Manual

Search results

Summary of Contents for DN41R

Reviews:

Related manuals for DN41R

Brands by name

Popular brands