background image

8

4.  Always keep your hands and body parts clear of 

moving parts to help prevent injuries.

 

!

 WARNING 

- ATTENDANTS

Make sure you read all warnings and follow all instructions 

in each section of this manual. Be aware that warnings that 

apply to the user also apply to you.

1.  Do not stand or sit on any portion of the wheelchair.

2.  You need to work with the user, and the user’s doctor, 

nurse or therapist, to develop safe methods best suited 

to your abilities and those of the user.

3.  To manually push the chair you must release the motor 

locks.

• Do not engage or disengage motor locks unless 

power to the chair is off. In addition, make sure both 

free wheel levers are completely engaged before 

turning the power on to ensure the wheelchair can 

be driven in a straight forward motion.

• Make sure you have full control over the chair when 

you release the motor locks. When you do so the 

chair will not have brakes.

• Make sure the chair is on level ground before you 

release the motor locks.

NOTE

 - To release the wheel locks the wheel chair may need to 

be rocked back and forth slightly several times before the lock 
will release.

4.   Propel this chair by the push handles only. They 

provide secure points for you to hold onto the rear of 

the chair to pre vent a fall or tip-over.

• Check to make sure push handle grips will not rotate 

or slip off.

 

!

 WARNING  

 B.  WEIGHT LIMIT

1.  The user plus items carried should never exceed the 

total weight capacity identified on your chair.

2.  Never use this chair for weight training if the total 

weight (user plus additional weights) exceeds weight 

capacity.

3.  Exceeding the weight limit is likely to damage the seat, 

frame, or fasteners, and may cause severe injury to 

you or others from chair failure.

4.  Exceeding the weight limit will void the warranty.

 

!

 WARNING 

 C.  CONTROLLER SETTINGS

Be aware that you may need to adjust the controller 

settings of your chair.

1.  Check and adjust the settings every six to twelve months.

2.  Consult your supplier to adjust the control settings 

immediately if you notice any change in your ability to:

• Control the joystick
• Hold your torso erect
• Avoid running into objects.

 

!

 WARNING 

 D. EMI

Read Section V to learn about EMI. To reduce the risk of 

unin tended brake release or chair movement:

1.  Never turn on or use a hand-held transceiver while 

power to your chair is on. Use extra care if you believe 

that such a device may be in use near your chair.

2.  Be aware of nearby radio or TV stations, and avoid 

coming close to them.

3.  If unintended movement or brake release occurs, turn 

your chair off as soon as it is safe.

 

!

 WARNING 

 E.  SAFETY CHECK-LIST

Before each use of this chair:

1.   Make sure the chair operates smoothly. Check for 

noise, vibration, or a change in ease of use. (These 

may indicate low tire pressure, loose fasteners, or 

damage to your chair).

• If you detect a problem, make sure to repair or 

adjust the chair. Your supplier can help you find and 

correct the problem.

2.   Make sure batteries are charged. Green lights on 

charge indicator will light up when charge is full. 

Yellow lights indicate battery charge level is getting 

low. Red lights indicate batteries are in immediate 

need of charging.

3.   When not in use, keep your chair in a clean, dry 

place.

t

 VI. GENERAL WARNINGS

Summary of Contents for R HybridHybrid








































Reviews: