manualshive.com logo in svg

AMX NetLinx NXB-KNX, Operation/Reference Manual

Share
Download
AMX NetLinx NXB-KNX Operation/Reference Manual Download Page 57

Appendix A: Telnet Commands

51

NXB-KNX Operation/Reference Guide 

Appendix A: Telnet Commands

Overview

The NXB-KNX supports Telnet communications. This type of terminal communication can be accessed 
remotely, via TCP/IP. 

Telnet is an insecure form of terminal communication, since it does not require a physical connection to the 
device to connect. Further, the Telnet interface exposes information to the network (which could be intercepted 
by an unauthorized network client).

Refer to the 

Terminal Commands

section on page 52 for a listing of all commands available in a terminal 

session.

Establishing a Terminal Connection Via Telnet

1.

In your Windows taskbar, go to 

Start > Run

 to open the Run dialog.

2.

Type 

cmd

 in the 

Open

 field and click 

OK

 to open an instance of the Windows command interpreter 

(Cmd.exe). 

3.

In the CMD (command), type "

telnet

" followed by a space and the NXB-KNX’s IP Address info.

 Example: 

>telnet XXX.XXX.XXX.XXX

4.

Press 

Enter

.

 

Unless Telnet security is enabled, a session will begin with a welcome banner:

Welcome to AMX v1.0.36 Copyright AMX LLC 2008

>

 

If Telnet security is enabled, type in the word

 login

 to be prompted for a Username and 

Password before gaining access to the NXB-KNX. 

5.

Enter your username to be prompted for a password.

 

If the password is correct you will see the welcome banner.

 

If the password is incorrect, the following will be displayed:

Login: User1

Password: *****

Login not authorized. Please try again.

After a delay, another login prompt will be displayed to allow you to try again. 

If after 5 prompts, the login information is not entered correctly, the following message will 
be displayed and the connection closed:

Login not allowed. Goodbye!

It is recommended that you make initial configurations as well as subsequent 
changes via the Web Console. Refer to the Configuration

section on page 5

.

If a connection is opened, but a valid a username / password combination is not 
entered (i.e. just sitting at a login prompt), the connection will be closed after one 
minute.

Summary of Contents for NetLinx NXB-KNX





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands