American Standard Advanced Clean 3.0 SpaLet User Manual Download Page 46

Page: 46 / 56

43 - EN

Troubleshooting

All Functions

Symptom

Cause

Solution

Page

All functions are

inoperable (pow-

er indicator is not

on).

Electricity is not supplied to power

outlet.

Check for a power failure, tripper

breaker, etc.

The power is turned off (power

indicator is not on).

Press the [Power] button and make

sure the power indicator on the seat

unit indicator section turns on.

The power plug is not connected to

the power outlet.

Completely connect the power plug

to the outlet.

Wait about 10 seconds before re-

connecting the power plug.

Voltage other than 120V is being

used.

Disconnect the power plug and have

the SpaLet

seat serviced

Corresponding

operations are

not performed

when switches on

the remote con-

trol are pressed

(power indicator

is on).

Batteries in the remote control

have completely discharged. (Bat-

tery LED is on

)

Replace with new batteries.

Batteries are installed in the remote

control in the incorrect orientation

of polarity.

Insert the batteries in the correct

orientation.

Remote control transmitter or re-

ceiver is dirty or wet.

Remove the dirt or water.

A fluorescent light with inverter bal

last is in use.

Turn off the light and try again.

If the SpaLet seat then operates

normally, there is no malfunction in

the product.

Remote control receiver is exposed

to direct sunlight.

Take the necessary action to pre-

vent exposure to direct sunlight.

*: When the remote control is installed on the wall opposite the receiver, the batteries may fully discharge before the battery LED

starts flashing.

Failures can be easily corrected in some cases. Please check the following items.

Summary of Contents for Advanced Clean 3.0 SpaLet

























































Search results

Summary of Contents for Advanced Clean 3.0 SpaLet

Reviews:

Related manuals for Advanced Clean 3.0 SpaLet

Brands by name

Popular brands

American Standard Advanced Clean 3.0 SpaLet, User Manual

Search results

Summary of Contents for Advanced Clean 3.0 SpaLet

Reviews:

Related manuals for Advanced Clean 3.0 SpaLet

Brands by name

Popular brands