![background image](http://html1.mh-extra.com/html/amano/pioneer-eclipse-pe440st/pioneer-eclipse-pe440st_operators-manual_2918200026.webp)
26
Belt Maintenance
1. Push machine to level surface.
2. Turn off LP cylinder and remove it.
3. Place the machine in the Rok-Bak position (See
“Rok-Bak & Pad Change” section).
4. Remove the Splash Plate.
5. Rotate the brushes/pad drivers and inspect the belt.
5. If cracks or excessive wear is present, the belt needs
to be replaced.
6. To check for the proper tightness, squeeze the belt
together. The belt should depress between 1/4” (0.6
cm) and 1/2” (1.3 cm).
Belt Replacement
APEC Part #: MP402100
A. Push machine to a level surface.
B. Place the machine in the Rok-Bak position (See Rok-
Bak section).
C. Remove both brushes allowing access to the pulley
cover.
D. Expose the belt by removing the pulley cover (four
1/4” screws) and the rear splash plate (two 1/4”
screws).
E. Remove the belt by slipping it off the center gearbox
pulley. Once the belt is off of the larger center pulley,
go ahead and take the belt off of the tensioner and
clutch.
F. With the belt off, check the fasteners and condition of
all the drive components.
G. Install new belt and re-attach the rear splash plate
and pulley cover.
H. Check belt for correct operation and proper tightness.
I. Return the machine to its operating position by
lowering it back to the floor. Return the handle to the
desired operating position.
Gearbox Maintenance
NOTE: Check gearbox oil level before each use. Add oil
if needed.
WARNING! The drive must be filled to proper level with
recommended lubricant before operation.
1. In order to drain the gearbox oil, the gearboxes need
to be removed from the machine. To do this:
a) Remove brush assembly from output shaft.
b) Loosen couplings that couple the three (3)
boxes together.
c) Loosen the pulley on the center gearbox.
d) Remove all retaining bolts.
e) Slip the boxes from the machine.
2. Remove the drain plugs (located in the sides of
gearboxes) and drain the oil into a drain pan. Allow
to drain completely.
3. With plug removed fill with AGMA 5EP or equivalent
gear lubricant as follows:
30”
: 5 oz. (14.8 ml) per box
38”
: 16 oz. (47 ml) per box
4. Replace plug and retighten. Re-assemble pulley,
couplings, brush assemblies, and gearboxes.
5. Dispose of used oil properly. Relubrication: Service
life and efficiency of gears and bearings will be
affected by oxidation or contamination of the
lubricating oil. Improved performance will be obtained
by periodic relubrication in accordance with the
following recommendations.
After an initial operating period of approximately 500
hours or six months, the housing should be completely
drained, preferably while warm. Refill housing to proper
level with fresh oil.
Tire Maintenance
Tire pressure should be checked before each use. Tires
should have equal pressure. The recommended tire
pressure is located on the side wall of tire.
Splash
Plate
Pulley
Cover
Summary of Contents for Pioneer Eclipse PE440ST
