background image

55

Emission Control Warranty Statement

Your Warranty Rights and Obligations

The California Air Resources Board and Amano Pioneer Eclipse 

Corporation is pleased to explain the emissions control system’s  

warranty on your 2016 small off-road engine.  In California, new 

equipment that use small off-road engines must be designed, built, and 

equipped to meet the State’s stringent anti-smog standards.  Amano 

Pioneer Eclipse Corporation must warrant the emissions control system 

on your small off-road engine for the period listed below provided there 

has been no abuse, neglect or improper maintenance of your equipment.  

Your emissions control system may include parts such as: carburetor’s 

or fuel injection system, ignition system, catalytic converters, fuel tanks, 

valves, filters, clamps, connectors, and other associated components.  

Also, included may be hoses, belts, connectors, sensors, and other 

emission-related assemblies.  Where a warrantable condition exists, 

Amano Pioneer Eclipse Corporation will repair your small off-road engine 
at no cost to you including diagnosis, parts and labor.

Manufacturer’s Warranty Coverage

This emissions control system is warranted for two years. If any       

emissions-related part on your equipment is defective, the part will be 
repaired or replaced by Amano Pioneer Eclipse Corporation.

Owner’s Warranty Responsibilities

(a) As the small off-road engine owner, you are responsible for  

performance of the required maintenance listed in your owner’s 

manual.  Amano Pioneer Eclipse Corporation recommends that you 

retain all receipts covering maintenance on your small off-road engine, 

but Amano Pioneer Eclipse Corporation cannot deny warranty solely 

for the lack of receipts or your failure to ensure the performance of all 

scheduled maintenance.

(b) As the small off-road engine owner, you should however be aware that 

Amano Pioneer Eclipse Corporation may deny you warranty coverage 

if your small off-road engine or a part has failed due to abuse, neglect, 

or improper maintenance or unapproved modifications.

(c) You are responsible for presenting your small off-road engine to an 

Amano Pioneer Eclipse Corporation distribution center or service 

center as soon as the problem exists.  The warranty repairs should be 

completed in a reasonable amount of time, not to exceed 30 days.  If 

you have a question regarding your warranty coverage, you should 
contact Amano Pioneer Eclipse Corporation at 1-800-367-3550.

Defects Warranty Requirements

(A) The warranty period begins on the date the engine or equipment is 

delivered to an ultimate purchaser.

(B) 

General Emissions Warranty Coverage.

 Amano Pioneer Eclipse 

Corporation as the manufacturer of each small off-road engine 

or equipment must warrant to the ultimate purchaser and each 

subsequent owner that the engine or equipment is:

(1) Designed, built, and equipped so as to conform with all 

applicable regulations adopted by the Air Resources Board; and

(2) Free from defects in materials and workmanship that causes the 

failure of a warranted part for a period of two years.

(C) The warranty on emissions-related parts will be interpreted as follows:

(1) Any warranted part that is not scheduled for replacement as 

required maintenance in the written instructions required by 

subsection (D) must be warranted for the warranty period defined 

in Subsection (B2).  If any such part fails during the period 

of warranty coverage, it must be repaired or replaced by the 

manufacturer according to Subsection (C4) below.  Any such part 

repaired or replaced under the warranty must be warranted for 
the remaining warranty period.

(2) Any warranted part that is scheduled only for regular inspection 

in the written instructions required by subsection (D) must be 

warranted for the warranty period defined in Subsection (B2).  

A statement in such written instructions to the effect of “repair 

or replace as necessary” will not reduce the period of warranty 

coverage.  Any such part repaired or replaced under warranty 

must be warranted for the remaining warranty period.

(3) Any warranted part that is scheduled for replacement as 

replacement as required maintenance in the written instructions 

required by subsection (D) must be warranted for the period 

of time prior to the first scheduled replacement point for that 

part.  If the part fails prior to the first scheduled replacement, the 

part must be repaired or replaced by the engine manufacturer 

according to Subsection (C4) below.  Any such part repaired or 

replaced under warranty must be warranted for the remainder of 

the period prior to the first scheduled replacement point for the 

part.

(4) Repair or replacement of any warranted part under the warranty 

must be performed at no charge to the owner at a warranty 

station.

(5) Notwithstanding the provisions of Subsection (C4) above, 

warranty services or Repairs must be provided at all 

manufacturer distribution centers that are franchised to service 

the subject engines.

(6) The owner must not be charged for diagnostic labor that leads 

to the Determination that a warranted part is in fact defective, 

provided that such diagnostic work is performed at a warranty 

station.

(7) The manufacturer is liable for damages to other engine 

components Proximately caused by a failure under warranty of 

any warranted part.

(8) Throughout the emissions warranty period defined in Subsection 

(B2), the manufacturer must maintain a supply of warranted parts 

sufficient to meet the expected demand for such parts.

(9) Any replacement part may be used in the performance of any 

warranty Maintenance or repairs and must be provided without 

charge to the owner.  Such use will not reduce the warranty 

obligations of the manufacturer.

(10) Add-on or modified parts that are not exempted by the 

Air Resources Board may not be used.  The use of any 

non-exempted add-on or modified parts will be grounds for 

disallowing a warranty claim. The manufacturer will not be liable 

to warrant failures of warranted parts caused by the use of a 

non-exempted add-on or modified part.

(11) The manufacturer issuing the warranty shall provide any 

documents that describe that manufacturer’s warrant procedures 

or policies within five working days of request by the Air 

Resources Board.

(D) 

Emission Warranty Parts List

(1) Fuel Metering System

(a) Carburetor, internal parts, and pressure regulator.

(b) Cold start enrichment system.

(2) Air Induction System

(a) Intake manifold.

(b) Air filter.

(3) Ignition System

(a) Spark Plugs.

(b) Magneto or electronic ignition system.

(c) Spark advance/retard system.

(4) Exhaust System

(a) Exhaust manifold.

(5) Miscellaneous Items Used in Above Systems

(a) Electronic Fuel Cut-off control.

(b) Vacuum, temperature, time sensitive valves, and switches.

(c) Hoses, belts, connectors, and assemblies.

Amano Pioneer Eclipse Corporation will furnish with each new engine 

written instructions for the maintenance and use of the engine by the 

owner.

Exception

:  This warranty does not apply to any machine models that do 

not have a catalyst muffler.

Small Off-Road Engine Certification Warranty Form

Summary of Contents for Pioneer Eclipse PE440ST





























































Reviews: