36
•
MN-35947
•
Rev 15
•
01/18
•
Combitherm® CT PROformance™ and CT Classic Series Installation Manual
#430 - 01/18
DUE TO ONGOING PRODUCT IMPROVEMENT, SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
WWW.ALTO-SHAAM.COM
*ELECTRICAL SERVICE CHARGE APPLIES
**NO-COST OPTION ON ELECTRIC MODELS
WeiGHt
SHiP DimenSionS
Pan CaPaCitY
NET
1100 lbs est
499 kg
(L x W x H) 53" x 53" x 87"*
FULL–SIZE:
20" x 12" x 2-1/2"
Forty (40)
PRODUCT MAXIMUM: 480 lb (218 kg)
SHIP
1157 lbs*
525 kg*
(1346 x 1346 x 2210mm)*
GN 1/1:
530 x 325 x 65mm
Forty (40)
VOLUME MAXIMUM: 300 quarts (380 liters)
*DOMESTIC GROUND SHIPPING INFORMATION. CONTACT FACTORY FOR
EXPORT WEIGHT AND DIMENSIONS.
GN 2/1:
650 x 530 x 65mm
Twenty (20)
**ON WIRE SHELVES ONLY. ADDITIONAL WIRE
SHELVES REQUIRED FOR MAXIMUM CAPACITY
**FULL–SIZE SHEET:
18" x 26" x 1"
Twenty (20)
eleCtriCal - CtP20-20e
(no CorD, no PluG, DeDiCateD CirCuit reQuireD)
WITH COMBISMOKER
®
OPTION
ECO STANDARD
**PROpower™ OPTION
ECO STANDARD
**PROpower™ OPTION
VOLTAGE
PH
HZ
AWG
CONNECTION
AMPS
kW
BREAKER
AMPS
kW
BREAKER
AMPS
kW
BREAKER
AMPS
kW
BREAKER
208 – 240
3
50/60 4/0
L1, L2, L3, G
137.6 – 158.8 49.6 – 66
150 – 175
172 – 198.5
57.8 – 77 175 – 200 140.1 – 161.6 50.1 – 66.7 150 – 175 174.5 – 201.3 58.4 – 77.7 200 – 225
380 – 415
3
50/60 1 - 1/0 L1, L2, L3, N, G
84.2 – 91.7
56.4 – 66
100
105.3 – 114.6 64.7 – 77
125
86.9 – 94.5 56.9 – 66.7
100
107.9 – 117.5 65.3 – 77.7
150
440 – 480
3* 50/60 2 – 1
L1, L2, L3, G
72.7 – 79.4
56.5 – 66
80
90.9 – 99.2
64.8 – 77
100
74.1 – 80.8 57.1 – 66.7 80 – 90
92.3 – 100.7 65.4 – 77.7
100
Water reQuirementS
Water QualitY StanDarDS
tWo (2) ColD Water inletS - DrinKinG QualitY*
one (1) treateD Water inlet: 3/4" NPT connection. Line pressure 30 psi minimum dynamic and
90 psi maximum static (200 to 600 kPa) at a minimum flow rate of 0.80 gpm (3 L/min).
one (1) untreateD Water inlet: 3/4" NPT connection. Line pressure 30 psi minimum dynamic and
90 psi maximum static (200 to 600 kPa) at a minimum flow rate of 2.64 gpm (10 L/min).
* Both inlets can be from same source. Divide using a manifold. Run one side through treatment device before running to oven.
Must meet line pressure and flow rate specifications for both inlets.
Water Drain: 1-1/2" (40mm) connection with a vertical vent to extend above the exhaust vent.
materials must withstand temperatures up to 200°F (93°C).
It is the sole responsibility of the owner/operator/purchaser of this equipment
to verify that the incoming water supply is comprehensively tested and
if required, a means of “water treatment” provided that would meet
compliance requirements with the published water quality standards shown
below. Non-compliance with these minimum standards will potentially
damage this equipment and/or components and void the original equipment
manufacturer’s warranty. Alto-Shaam recommends using OptiPure
®
[www.
optipurewater.com] products to properly treat your water.
Contaminant
Free Chlorine
Hardness
Chloride
pH
Silica
Total Dissolved Solids (tds)
inlet Water requirements
Less than 0.1 ppm (mg/L)
30-70 ppm
Less than 30 ppm (mg/L)
7.0 to 8.5
Less than 12 ppm (mg/L)
Treated line: 50-125 ppm
Untreated line: 50-360 ppm
ClearanCe reQuirementS
left:
0" (0mm)
18" (457mm) recommended service access
riGHt:
0" (0mm) Non-combustible surfaces
2" (51mm) door swing or combustible surfaces
toP:
20" (508mm) for air movement
bottom:
5-1/8” (130mm) for legs, air aintake
baCK:
4" (102mm)
4-5/16” (109mm) optional plumbing kit
inStallation reQuirementS
• Oven must be installed level.
• Hood installation is required.
• Water supply shut-off valve and back-flow preventer when required by local code.
DimenSionS: H x W x D
eXterior:
79-1/4" x 43-3/4" x 47" (2012mm x 1111mm x 1192mm)
eXterior WitH reCeSSeD Door:
79-1/4" x 48-3/4" x 47" (2012mm x 1238mm x 1192mm)
interior:
60-7/16" x 24-1/4" x 32-3/4" (1535mm x 616mm x 832mm)
CTP20-20E
ELECTRIC BOILER-FREE
C (at bottom of oven)
47-7/8" (1215mm)
47" (1192mm)
43-3/4" (1111mm)
B
A
E
33-9/16" (852mm)
1-15/16" (49mm)
41-7/8" (1063mm)
1" (24mm)
79-1/4" (2012mm)
4-1/2
" (1
14mm)
4-1/4" (108mm)
7-15/16" (202mm)
D
59-1/4
" (1504mm)
33-13/16
" (858mm)
11-13/16
" (299mm)
9-3/16
" (233mm)
B
D
A
E
3-1/4" (81mm)
4-3/16"
(106mm)
4-1/8" (105mm)
5" (126mm)
1-11/16" (42mm)
73-5/8" (1869mm)
A= UNTREATED WATER
B= TREATED WATER
C= ELECTRICAL
D= GAS
E= WATER DRAIN
