manualshive.com logo in svg

Alps Electric SPEEDGLIDER, Operator'S Manual

Share
Download
Alps Electric SPEEDGLIDER Operator'S Manual Download Page 8

AIR LOGIC POWER SYSTEMS (ALPS) 

  

SAFETY

 

SPEEDGLIDER 

 ADVANCED OPERATOR MANUAL 

 7 

 TM 2012-005 REV00 © 10/25/2012 

Safety 

Safety: Warning Labels and Descriptions 

Safety is critical  at all times. The ALPS NGR Rotary machine is equipped with a full  complement of warning 
decals and labels. A standard series of warning and caution labels are in place to inform the operator of certain 
hazards relative to the function of this machine. Please observe all of these warnings. 

 

DANGER! ARC, SHOCK, AND FLASH HAZARD

: 

The potential for serious or fatal injury exists. Located on the outer door surface of the High-Voltage Control enclosure. 
Do not open to explore or attempt to affect repairs in this area. In case of breakdown, initiate Lock-Out Tag-Out 
procedures to secure the machine. Notify authorized personnel. 

 

WARNING! LOW VOLTAGE CONTROL ENCLOSURE 

This label is displayed on the outside of the Low Voltage Control enclosure. This area controls power to all electronic 
modules on the machine. A potential for serious bodily injury or death exists. In case of breakdown, initiate Lock-Out 
Tag-Out procedures to secure the machine. Notify authorized personnel. 

 

RISK OF HOT SURFACES HAZARD 

This symbol can be found in areas where a potential burn hazard exists. SpeedGlider servo motors have hot surfaces. 
Do not touch motor surfaces while in operation or after being recently shut down. 

  

 

Summary of Contents for SPEEDGLIDER



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands