manualshive.com logo in svg

Alps Electric SPEEDGLIDER, Operator'S Manual

Share
Download
Alps Electric SPEEDGLIDER Operator'S Manual Download Page 21

AIR LOGIC POWER SYSTEMS (ALPS) 

  

THE SETTINGS MENU

 

SPEEDGLIDER 

 ADVANCED OPERATOR MANUAL 

 20 

 TM 2012-005 REV02 © 03/19/2013 

The Settings Menu 

Settings Introduction 

 
 
 

 

The leak tests performed by the SpeedGlider depend on the proper settings of the Test Timers, Pressures, and 
Reject Limits.  The Settings Menu is where all the perimeters for the required leak test as well as machine speeds 
and timing can be viewed and edited.   

Test Pressures & Reject Limits Introduction 

 

 
These Menus contain the time values and perimeters 
required to perform leak tests on the SpeedGlider.  
Adjustments to test setting values are done in these 
menus.  

 

 

 
 
 
 
 
 
 
SETTINGS MENU 

DESCRIPTION TABLE 

Setting 

Description 

Fill Time 
Range: .01 to 10 
seconds 

When the start fill time pressure” is reached the “Fill Time” begins to count when the fill 
time reaches the value entered expires the fill valve will off.  

Maximum fill time 
 
Range: .02 to 15 
seconds 

Time allowed for the “start fill time pressure: to reach the pressure entered. The container 
will be rejected for a “Max Fill Failure” if the pressure does not reach the required amount 
in the time given. The normal setting is approximately .150 seconds.   

Test 1 Time 
 
Range: .005 to 10 
seconds 

Time allowed for test 1 container stabilization time. The normal setting for test 1 is around 
.1 seconds for smaller container and .2 for larger more flexible containers.  The test 1 time 
works in conjunction with the reject limits settings for Minimum test 1 percent and 
Maximum test 1 percent. If the container falls out of the window range set of min and max 
set in the reject limits for test 1 in the test 1 time frame the container will be rejected 

Test 2 Time 
 
Range: 0 to 20 
seconds 

 

Time allowed for test 2 small hole detection. The time set here should always be as long 
as possible. To set properly set the time high enough to get “test to long” alarms and then 
back down incrementally until Alarm ceases. The test 2 time works in conjunction with the 
reject limits settings for Minimum test 2 percent and Maximum test 2 percent. If the 
container falls out of the window range set of min and max set in the reject limits for test 2 
in the test 2 time frame the container will be rejected 

 
 
 

 

Summary of Contents for SPEEDGLIDER



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands