manualshive.com logo in svg

Alps Electric SPEEDGLIDER, Operator'S Manual

Share
Download
Alps Electric SPEEDGLIDER Operator'S Manual Download Page 27

AIR LOGIC POWER SYSTEMS (ALPS) 

  

THE SETTINGS MENU

 

SPEEDGLIDER 

 ADVANCED OPERATOR MANUAL 

 26 

 TM 2012-005 REV02 © 03/19/2013 

 

 

 

 

 

 

 

 

 

 

 

 

Notice

: Depending on how far the test probe adjustment moved during the timing screw adjustment the Container 

At Test photo eye will need to be moved in perspective to the encoder window of 1500 to 2000.

 

 

 

 
 
 
 
 
 
 
 
 
 
 

 

 

13. Place a container in the timing screw pocket near the 
Container At Test photo eye 

 

10.  By hand advance the timing screw to 1500 the Window 

should come ON GREEN. 

11.  Advance timing screw to 1600. The Container At Test 

indication should start to come ON GREEN as you advance 
the timing screw. 

12.  If the Container at Test does not turn ON GREEN adjust the 

photo eye towards the leading edge of the container until the 
indicator comes 

13.  Tighten the photo eye into place. 

 

8.  Adjust timing screw using a 4 mm Allen wrench 

a.  Loosen both set screws. 
b.  Using one hand hold on to the shaft (S) 
c.  With the other hand rotate the timing screw (T)  

i.  For situation (A) rotate backwards opposite 

the flow direction.* 

ii.  For situation (B) rotate forward with flow 

direction.* 

d.  Tighten set screws. 

9.  Run containers through the timing screw again and check for 

proper alignment (C).  If the timing screw and test probe are 
not aligned redo step 5. 

 

* Rotation adjustment of timing screw is proportional to how far 
the container test probes are off. 

S 

T 

 
14.  Continue to rotate the timing screw forward by hand. 

Notice at some point near or before 2000 the 
Container At Test indicator turns OFF. 

15.  This procedure is complete 

 

Summary of Contents for SPEEDGLIDER



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands