manualshive.com logo in svg

Alps Electric SPEEDGLIDER, Operator'S Manual

Share
Download
Alps Electric SPEEDGLIDER Operator'S Manual Download Page 57

AIR LOGIC POWER SYSTEMS (ALPS) 

  

CONTAINER CHANGE OVER

 

SPEEDGLIDER 

 ADVANCED OPERATOR MANUAL 

 56 

 TM 2012-005 REV00 © 10/25/2012 

 

15.  Entering reject limits 

Navigate to the manual test menu for one of the heads to help set reject 
limits for test 1 and test 2 

16.  Perform a Manual Test and 

enter % values 

Ranges: 

Minimum test 1 percent 
& 
Maximum test 1 percent 
 
Range: -75 to 75% 
Min: .5 to 75 % 
Minimum test 2 percent 
& 
Maximum test 2 percent 
 
Range: -75 to 75% 

 

A.  Place a known good container underneath a test probe and perform a 

Manual Test

.  If there was a good seal then then the test probe will stay 

engaged for the Test 1 and Test 2 times. 

B.  Take notice of the Test 1 and 2 result gauges. Set the Max percentage 

approximately 10 percentage points above the maximum values reported 
on the gauges for both Test 1 and if Test 2. (If Test 2 is being used).  

C.   Check for consistency by performing several 

Manual Tests 

to ensure 

the percentage readings fall within the ranges entered.  

17.  Perfom a Manual Self Test 

 

Performing a 

Manual Self Test

 on the same known good container. This will 

open a leak path to the installed orifices. 
 
A.  Take notice of the Test 1 and 2 result gauges again. This time they 

should be well above (approximately 10 percent points) the acceptable 
limits. If this is not the case the orifice maybe too small for the test 
settings or the test setting and speed may need to be reconsidered. 

B.  Check for consistency by performing several 

Manual Self Tests

. Doing 

this will ensure the test settings are accurate. 

 
 

18.  Poocedure is Complete 

 

 

 

Summary of Contents for SPEEDGLIDER



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands