manualshive.com logo in svg

Alps Electric SPEEDGLIDER, Operator'S Manual

Share
Download
Alps Electric SPEEDGLIDER Operator'S Manual Download Page 43

AIR LOGIC POWER SYSTEMS (ALPS) 

  

THE SUPERVISOR MENU

 

SPEEDGLIDER 

 ADVANCED OPERATOR MANUAL 

 42 

 TM 2012-005 REV00 © 10/25/2012 

 

Manual Test Display Description 

The Manual Test has eight basic parts to it. 

 

 

 

 

 

 

 

 

Part 

Description 

Part 1: Manual Test Result

 

Indicates leak test PASS or reason for failure. 

Part 2: Probe and Fill 
regulator gauge readings 

 

Indicates what the probe and fill regulators are set at.  

Part 3: Part Pressure 
Gauge 

 

The Part Pressure gauge is a necessary tool for setting fill pressure. Typically 
the fill pressure is set according to the container size. Smaller containers 
=less fill pressure and larger containers = more fill pressure.  For more on this 
see new container setup procedures. 

Notice that the PART PRESSURE gauge values do not have gray entry 
boxes associated with them.  This is because the values are hard coded at 
0.5 and 25 percent and cannot be changed by the operator. 

The current analog to digital value for PART PRESSURE 

gauge is shown in the black. This digital read out will only show real time 
values.  

 When the manual test button is pushed The MIN and MAX 

indicators will remain green if the container is set for the proper fill pressure. 

If the container is out range one of the indicator will turn 

red and stay red until a successful in range test is accomplished.  

The manual test result displays will indicate the reason. 

 

 

Part 1 

Part 2 

Part 3 

Summary of Contents for SPEEDGLIDER



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands