background image

14

Subject to change without notice.
83054800bUK – Translation into English of the original German operating manual  ait-deutschland GmbH

1  Wall penetration
2  Air duct
3  Rolling O-ring joint
4  Waterstop tape (do not 

attach until after the unit 
connections have been fixed)

 NOTE.

 

After the other end of the air duct has also been 
fixed onto the heat pump, seal off the opening that 
still exists between the wall penetration and the air 
duct by attaching the waterstop tape supplied.

FIXING THE AIR DUCTS ONTO THE HEAT PUMP

  Clip on the mounting strip and use special screws to 

fix onto the places provided for this purpose on the 
air duct for the air inlet side…

  Glue the connection frame supplied onto the edge of 

the air duct…

  Position the air duct on the respective air opening of 

the air inlet side…

  At the air inlet side of the heat pump, hook 4 of the 

tension springs supplied in the holes provided for this 
purpose…

 Hook the tension springs into the mounting strip 

screwed onto the air duct…

  Fix the protective caps above the mounting strip…

1  Finished external façade

 NOTE.

 

Wall penetrations are used for fixing in the 
masonry opening, to avoid cold bridges with the 
masonry, and to install weather and rain louvres 
and wire mesh.

ASSEMBLY AND INSTALLATION OF THE AIR DUCTS

  Take the elements for assembling the air ducts from 

the relevant box…

  The air ducts are assembled by pushing them together 

as is described in the “Assembly and installation of the 
wall penetration(s)” section,   –  .

FIXING THE AIR DUCTS IN THE WALL PENETRATION

  Pull the rolling O-ring joint supplied over one end of 

an air duct…

  Push the air duct into the wall penetration with this 

end first.

Summary of Contents for LW 160H/V









































Reviews: