ALLIANCE SWNNC2HP115TQ01 Original Instructions Manual Download Page 75

Page: 75 / 90

To exit the Water Level Test, press the WARM (<) keypad. The
control will return to the Testing Mode.

Configuration 1 Display Test

d 29

This option shows the machine configuration values. To start test,
control must be in the Testing Mode. Refer to

How to Enter Test-

ing Feature

at the beginning of this section.

To enter, press the START (enter) keypad. For configuration val-
ue #1, the display will show

A XXX

is a number correspond-

ing to whether or not coin drops are connected, a card reader or
network board are connected, or whether the life-test jumper is
present. Refer to

Table 15

To exit a Configuration Display Test, press the WARM (<) key-
pad. The control will return to the Testing Mode.

Each column of the table below contains a unique combination of
the words “YES” and “NO” that indicates if that column’s con-
nection is present.

Testing Machine and Electronic Control Functions

DO NOT COPY or TRANSMIT

Part No. 204370ENR1

Summary of Contents for SWNNC2HP115TQ01



























































































Search results

Summary of Contents for SWNNC2HP115TQ01

Reviews:

Related manuals for SWNNC2HP115TQ01

Brands by name

Popular brands

ALLIANCE SWNNC2HP115TQ01, Original Instructions Manual

Search results

Summary of Contents for SWNNC2HP115TQ01

Reviews:

Related manuals for SWNNC2HP115TQ01

Brands by name

Popular brands