ALLIANCE SWNNC2HP115TQ01 Original Instructions Manual Download Page 57

Page: 57 / 90

How to Program Special Vend 1 Wash Status

Agitate Steps Subtracted Minutes

SP1 21

This option allows the owner to subtract time from any agitate
steps that have their status set to Wash in Special Vend 1.
1. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the programmable Special Vend 1 options until

SP1

appears in the display.

2. When

SP1 21

appears in the display, press the START (en-

ter) keypad. The current value will appear in the display.

NOTE: To go back to the current programmable
Special Vend 1 option without changing the value,
press the WARM (<) keypad.

3. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to in-

crease or decrease the value of the active digit and the START
keypad to enter the value of the digit and advance to the next
digit.

4. Press the START (enter) keypad when the correct value ap-

pears in the display. The new value is saved and the next op-
tion will appear in the display.

How to Program Special Vend 1 Cycle Modifier

Default Value

SP1 22

This option allows the owner to set the default cycle modifier that
should be selected any time that Ready Mode is entered.

0 = Modifier LIGHT, 1 = Modifier MEDIUM, 2 = Modifier
HEAVY.
1. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the programmable Special Vend 1 options until

SP1

appears in the display.

2. When

SP1 22

appears in the display, press the START (en-

ter) keypad. The current value will appear in the display.

NOTE: To go back to the current programmable
Special Vend 1 option without changing the value,
press the WARM (<) keypad.

3. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to in-

crease or decrease the value of the active digit and the START
keypad to enter the value of the digit and advance to the next
digit.

4. Press the START (enter) keypad when the correct value ap-

pears in the display. The new value is saved and the next op-
tion will appear in the display.

How to Program Special Vend 1 Cycle Modifier

MEDIUM Key #1 Vend Price

SP1 23

1. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the programmable Special Vend 1 options until

SP1

appears in the display.

2. When

SP1 23

appears in the display, press the START (en-

ter) keypad. The current value will appear in the display.

NOTE: To go back to the current programmable
Special Vend 1 option without changing the value,
press the WARM (<) keypad.

3. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to in-

crease or decrease the value of the active digit and the START
keypad to enter the value of the digit and advance to the next
digit.

4. Press the START (enter) keypad when the correct value ap-

pears in the display. The new value is saved and the next op-
tion will appear in the display.

How to Program Special Vend 1 Cycle Modifier

HEAVY Key #2 Vend Price

SP1 24

1. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the programmable Special Vend 1 options until

SP1

appears in the display.

2. When

SP1 24

appears in the display, press the START (en-

ter) keypad. The current value will appear in the display.

NOTE: To go back to the current programmable
Special Vend 1 option without changing the value,
press the WARM (<) keypad.

3. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to in-

crease or decrease the value of the active digit and the START
keypad to enter the value of the digit and advance to the next
digit.

4. Press the START (enter) keypad when the correct value ap-

pears in the display. The new value is saved and the next op-
tion will appear in the display.

How to Program Special Vend 1 Cycle Modifier

MEDIUM Key #1 Options

SP1 25

1. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the programmable Special Vend 1 options until

SP1

appears in the display.

2. When

SP1 25

appears in the display, press the START (en-

ter) keypad. The current value will appear in the display.

NOTE: To go back to the current programmable
Special Vend 1 option without changing the value,
press the WARM (<) keypad.

3. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to in-

crease or decrease the value to enable the desired options to
be active when the MEDIUM keypad is active. Refer to

Table

4. Press the START (enter) keypad when the correct value ap-

pears in the display. The new value is saved and the next op-
tion will appear in the display.

How to Program Special Vend 1 Cycle Modifier

HEAVY Key #2 Options

SP1 26

1. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the programmable Special Vend 1 options until

SP1

appears in the display.

Programming Control

DO NOT COPY or TRANSMIT

Part No. 204370ENR1

Summary of Contents for SWNNC2HP115TQ01



























































































Search results

Summary of Contents for SWNNC2HP115TQ01

Reviews:

Related manuals for SWNNC2HP115TQ01

Brands by name

Popular brands

ALLIANCE SWNNC2HP115TQ01, Original Instructions Manual

Search results

Summary of Contents for SWNNC2HP115TQ01

Reviews:

Related manuals for SWNNC2HP115TQ01

Brands by name

Popular brands