ALLIANCE SWNNC2HP115TQ01 Original Instructions Manual Download Page 89 | Manualshive

Page: 89 / 90

background image

Communications Mode

Infra-red Communications

The Infra-red Communications feature allows the washer control
to communicate with an external device. The washer control can
be programmed and have its data read without using the keypad.
It may also be used to start and stop various diagnostic tests.

How to Begin Communications with an External

Device

The control will go blank and the display will show

-C-

until the

communication is complete. If an error occurs that terminates
communication, the display will show

EIXX

(

XX

represents the

error code).

NOTE: The Infra-red Communications option must be
turned on.

Card Reader Communications - Card

Models Only

The Card Reader Communications feature allows the washer con-
trol to communicate with the card reader. The washer control can
be programmed for a limited number of options and have its data
read without using the keypad.

Network Communications

The Network Communications feature allows the washer control
to communicate with a network. The washer control can be pro-
grammed and have its data read without using the keypad.

Communications Mode

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

89

Part No. 204370ENR1

«
...
87
88
89
90
»

Summary of Contents for SWNNC2HP115TQ01



























































































Reviews:

No comments

Related manuals for SWNNC2HP115TQ01

Brand: DC Pages: 2

Brand: Waterline Pages: 31

Brand: Kärcher Pages: 20

Brand: ZANKER Pages: 40

Brand: Indesit Pages: 72

Brand: Smeg Pages: 27

Brand: NABO Pages: 32

Hotpoint HDA3400G

Brand: Hotpoint Pages: 2

Brand: Jackson MSC Pages: 64

Brand: CORBERO Pages: 17

Brand: Smeg Pages: 27

Brand: Smeg Pages: 38

LVSLS11C45GZ17S

Brand: Saba Pages: 35

Brand: CaterChef Pages: 44

WA80CG4545 Series

Brand: Samsung Pages: 48

Brand: Electrolux Pages: 40

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands