ALLIANCE SWNNC2HP115TQ01 Original Instructions Manual Download Page 20

Page: 20 / 90

TLW17R_SVG

Manual Mode: Enter by opening the service door for at least 1 second
and then closing service door. Then press LIGHT and NORMAL keypads
at same time.

"rAPid"

Rapid Advance

"Prog "

Manual Programming

"AUdit"

Manual Read

Audit

"rESEt"

Manual Reset

"diAg"

Diagnostic

Tests

Press the
DELICATES or
the COLD keypad to
scroll through the
Manual Mode options.

Press the START keypad to
begin Rapid Advance cycle and
to advance through cycle steps.

Press the START keypad to
enter Manual Programming.
Refer to Manual
Programming flowchart.

"CyCLES"

Total machine cycles

"Coin 1"

Total coins #1

"PULSE"

Total start pulses

"Coin 2"

Total coins #2

Press the
DELICATES
or the
COLD
keypad to
scroll through
the Audit
options.

Press the
START keypad.

Press the START keypad to enter
Manual Reset Mode.

Press the START keypad to
enter Diagnostic Tests. Refer to
Diagnostic Tests flowchart.

Press the START (enter)
keypad to read audit.

"rAPCyC"

Total Rapid Advance Cycles

"rCoin1"

Resettable Coin #1 count

"rUnHrs"

Total run hours

Press the START (enter)
keypad to read audit.

"rCoin2"

Resettable Coin #2 count

Press the START (enter)
keypad to read audit.

"rCyCLE"

Resettable Machine Cycle count

Press the START (enter)
keypad to read audit.

Figure 3

Entering the Manual Mode

DO NOT COPY or TRANSMIT

Part No. 204370ENR1

Summary of Contents for SWNNC2HP115TQ01



























































































Search results

Summary of Contents for SWNNC2HP115TQ01

Reviews:

Related manuals for SWNNC2HP115TQ01

Brands by name

Popular brands

ALLIANCE SWNNC2HP115TQ01, Original Instructions Manual

Search results

Summary of Contents for SWNNC2HP115TQ01

Reviews:

Related manuals for SWNNC2HP115TQ01

Brands by name

Popular brands