ALLIANCE SWNNC2HP115TQ01 Original Instructions Manual Download Page 69

Page: 69 / 90

Manual Reset

This feature allows the owner to reset the washer control’s pro-
gramming data to the factory default settings by pressing a se-
quence of pads on the control.

How to Enter Manual Reset

1. Control must be in Manual Mode. Refer to

How to Enter the

Manual Mode

2. Press the DELICATES (

∧

) or the COLD (

∨

) keypad until

Prog

appears in the display. Press the START (enter) keypad,

and

AtS 1

will appear in the display.

3. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the programmable options until

rESEt

appears in the

display.

4. Press the START (enter) keypad.

will appear in the dis-

play.

5. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to change

the value to

yes

6. Press the START (enter) keypad when the correct value ap-

pears in the display.

Manual Reset

DO NOT COPY or TRANSMIT

Part No. 204370ENR1

Summary of Contents for SWNNC2HP115TQ01



























































































Search results

Summary of Contents for SWNNC2HP115TQ01

Reviews:

Related manuals for SWNNC2HP115TQ01

Brands by name

Popular brands

ALLIANCE SWNNC2HP115TQ01, Original Instructions Manual

Search results

Summary of Contents for SWNNC2HP115TQ01

Reviews:

Related manuals for SWNNC2HP115TQ01

Brands by name

Popular brands