ALLIANCE SWNNC2HP115TQ01, Original Instructions Manual

Page: 58 / 90

2. When
SP1 26
appears in the display, press the START (en-
ter) keypad. The current value will appear in the display.
NOTE: To go back to the current programmable
Special Vend 1 option without changing the value,
press the WARM (<) keypad.
3. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to in-
crease or decrease to enable the desired options to be active
when the HEAVY keypad is active. Refer to
Table 1 .
4. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Special Vend 2 Days Enable
SP2
This option allows the owner to enable or disable a second spe-
cial vend. Special Vend 2 can be programmed using an external
device or network. The owner may also turn the Special Vend 2
option on or off.
1. Control must be in Manual Mode. Refer to
How to Enter the
Manual Mode .
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to scroll
through the programmable options until
SP2
appears in the
display.
4. When
SP2
appears in the display, press the START (enter)
keypad. The current Special Vend 2 Days Enable status will
appear in the display.
on
= Option Enabled
oFF
= Option Disabled (factory default setting)
5. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Special Vend 3 Days Enable
SP3
This option allows the owner to enable or disable third special
vend. Special Vend 3 can be programmed using an external de-
vice or network. The owner may also turn the Special Vend 3 op-
tion on or off.
1. Control must be in Manual Mode. Refer to
How to Enter the
Manual Mode .
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to scroll
through the programmable options until
SP3
appears in the
display.
4. When
SP3
appears in the display, press the START (enter)
keypad. The current Special Vend 3 Days Enable status will
appear in the display.
on
= Option Enabled
oFF
= Option Disabled (factory default setting)
5. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Special Vend 4 Days Enable
SP4
This option allows the owner to enable or disable a fourth special
vend. Special Vend 4 can be programmed using an external de-
vice or network. The owner may also turn the Special Vend 4 op-
tion on or off if desired.
1. Control must be in Manual Mode. Refer to
How to Enter the
Manual Mode .
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to scroll
through the programmable options until
SP4
appears in the
display.
4. When
SP4
appears in the display, press the START (enter)
keypad. The current Special Vend 4 Days Enable status will
appear in the display.
on
= Option Enabled
oFF
= Option Disabled (factory default setting)
5. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cycle Modifier Programming
CNP-
This option allows the owner to program the machine to offer ex-
tra wash time, extra rinse time, a warm rinse, or any combination
of the above to the customers for an added vend price. This op-
tion is used when MEDIUM or HEAVY is selected using the
Modifier keypad.
How to Program Default Cycle Modifier
CNP 1
This option allows the owner to set the Default Cycle Modifier.
1. Control must be in Manual Mode. Refer to
How to Enter the
Manual Mode .
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
58 Part No. 204370ENR1