background image

Configura-

tion Value

Life Test

Jumper

Present

Comm

Board "B"

Header

Present

Comm

Board "A"

Header

Present

Vend Con-

nection

Present

Coin Drop

#2 Present

Coin Drop

#1 Present

0

NO

NO

NO

NO

NO

NO

1

NO

NO

NO

NO

NO

YES

2

NO

NO

NO

NO

YES

NO

3

NO

NO

NO

NO

YES

YES

4

NO

NO

NO

YES

NO

NO

5

NO

NO

NO

YES

NO

YES

6

NO

NO

NO

YES

YES

NO

7

NO

NO

NO

YES

YES

YES

8

NO

NO

YES

NO

NO

NO

9

NO

NO

YES

NO

NO

YES

10

NO

NO

YES

NO

YES

NO

11

NO

NO

YES

NO

YES

YES

12

NO

NO

YES

YES

NO

NO

13

NO

NO

YES

YES

NO

YES

14

NO

NO

YES

YES

YES

NO

15

NO

NO

YES

YES

YES

YES

16

NO

YES

NO

NO

NO

NO

17

NO

YES

NO

NO

NO

YES

18

NO

YES

NO

NO

YES

NO

19

NO

YES

NO

NO

YES

YES

20

NO

YES

NO

YES

NO

NO

21

NO

YES

NO

YES

NO

YES

22

NO

YES

NO

YES

YES

NO

23

NO

YES

NO

YES

YES

YES

24

NO

YES

YES

NO

NO

NO

25

NO

YES

YES

NO

NO

YES

26

NO

YES

YES

NO

YES

NO

27

NO

YES

YES

NO

YES

YES

28

NO

YES

YES

YES

NO

NO

29

NO

YES

YES

YES

NO

YES

30

NO

YES

YES

YES

YES

NO

Table 15 

 continues...

Testing Machine and Electronic Control Functions

©

 Copyright, Alliance Laundry Systems LLC -

 DO NOT COPY or TRANSMIT

  76

  Part No. 204370ENR1

Summary of Contents for SWNNC2HP115TQ01



























































































Reviews: