Alliance Laundry Systems BD3LLFGS401UW01 Troubleshooting Manual Download Page 18

Page: 18 / 71

513447

Dryer Troubleshooting

6. Dryer Heating Assembly Does Not Heat or Burner Does Not Ignite

Dryer heating assembly does not
heat or burner does not ignite.

Is exhaust

system

improper or

inadequate?

Refer to

Installation
Instructions

(supplied with
unit) for
exhaust
requirements.

Is exhaust

duct made of

plastic or thin

foil?

Replace with
rigid or semi-
rigid metal
exhaust duct.

Yes

Is house fuse

blown or

circuit breaker

tripped?

Check fuses or
circuit breakers. A
240 Volt electric
heat dryer uses two
fuses. Make sure
both fuses are
good.

Yes

Electric

Models: Is

heater assembly

inoperative?

Test heater
assembly and
replace if cold
Ohms do not
read between
9 and 10.5
Ohms.

Yes

Electric

Models: Is

thermal fuse
inoperative?

Test thermal
fuse and
replace if
inoperative.
Refer to

Test

Procedures

section.

Yes

DRY1848Sa

Yes

Continued on

next page.

Is limit

thermostat

inoperative?

Test thermostat
and replace if
inoperative.
Refer to

Test

Procedures

section.

Is drive

motor switch

inoperative?

Test switch
and replace if
inoperative.

Is termperature

selector switch

set at FLUFF/NO

HEAT or

inoperative?

Reset or test

switch and

replace if

inoperative.

Yes

Summary of Contents for BD3LLFGS401UW01








































































Search results

Summary of Contents for BD3LLFGS401UW01

Reviews:

Related manuals for BD3LLFGS401UW01

Brands by name

Popular brands

Alliance Laundry Systems BD3LLFGS401UW01, Troubleshooting Manual

Search results

Summary of Contents for BD3LLFGS401UW01

Reviews:

Related manuals for BD3LLFGS401UW01

Brands by name

Popular brands