Alliance Laundry Systems BD3LLFGS401UW01 Troubleshooting Manual Download Page 63 | Manualshive

Page: 63 / 71

background image

513447

61

Test Procedures

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the dryer is properly grounded.

W001R1

WARNING

34. Motor Switch

a. Remove motor and exhaust fan assembly.
b. Remove the two motor switch attaching screws.

Refer to

Figure 32

. Disconnect switch leads.

Remove motor switch.

c. Remove thermal overload protector.

NOTE: The thermal overload protector is unique
to the motor from which it was removed and should
only be used on that motor. To reduce the risk of
overheating the motor, do not use any thermal
overload protector other than the one taken from
the inoperative motor switch in step 3.

(1)

Motor with Switch on Blower End

Using a small bladed screwdriver, press the
thermal overload protector mounting tab
downward and remove the thermal
overload protector from the inoperative
motor switch. Refer to

Figure 28

.

Figure 28

D02

9

KE3A

Mounting

Tab

Thermal

Overload

Protector

Motor

Switch

«
...
61
62
63
64
65
...
»

Summary of Contents for BD3LLFGS401UW01








































































Reviews:

No comments

Related manuals for BD3LLFGS401UW01

Brand: Gaggenau Pages: 18

Brand: Indesit Pages: 16

Brand: T3 Pages: 27

Brand: Omcan Pages: 20

Brand: DeLonghi Pages: 34

Brand: Kalorik Pages: 62

Brand: Franke Pages: 4

Brand: Masterbuilt Pages: 16

Brand: Beko Pages: 76

Brand: Zanussi Pages: 2

Brand: Zanussi Pages: 2

Brand: Kenmore Pages: 8

Brand: Kenmore Pages: 8

Brand: Kenmore Pages: 4

EXTRAKLASSE 610

Brand: Siemens Pages: 16

ultra Sense WT46E300US

Brand: Siemens Pages: 24

EXTRAKLASSE 660

Brand: Siemens Pages: 20

IQ300 WT45N202GB

Brand: Siemens Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands