Alliance Laundry Systems BD3LLFGS401UW01 Troubleshooting Manual Download Page 28 | Manualshive

Page: 28 / 71

background image

26

513447

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Dryer Troubleshooting

14. Clothes Are Too Hot When Removed From Dryer

Clothes are too hot when
removed from dryer.

Is exhaust

system

improper or

inadequate?

Refer to

Installation
Instructions

(supplied with unit)
for exhaust
requirements.

Yes

Were clothes

removed from

dryer before

cycle has

completed?

No

Allow the dryer to
complete the
cycle through the
cool-down to the
OFF position.

Yes

Is cycling

thermostat

inoperative?

Test cycling
thermostat and
replace if
inoperative.

No

Yes

DRY1855S

Are seals

inoperative
(air leaks)?

Check and replace any inoperative
seals in the following areas:
1. Seal between loading door and
front panel.
2. Seal between front panel and front
bulkhead.
3. Seal between blower cover and air
duct.
4. Seal between cylinder and front or
rear bulkhead.
5. Gap between air duct and filter
mounting.

Add additional
cool-down time.

Is

accumulator

inoperative

(not allowing

cool-down)?

Test and replace
accumulator if
inoperative. Refer
to

Test Procedures

section.

No

Yes

No

No

Yes

«
...
26
27
28
29
30
...
»

Summary of Contents for BD3LLFGS401UW01








































































Reviews:

No comments

Related manuals for BD3LLFGS401UW01

Brand: Panasonic Pages: 44

Brand: Vitek Pages: 24

Brand: T-Fal Pages: 34

Brand: Salton Pages: 11

Brand: Midea Pages: 28

Brand: Optimum Pages: 16

Brand: Marta Pages: 8

Brand: Caple Pages: 25

Brand: Hyundai Pages: 44

Brand: Indesit Pages: 84

Brand: Farouk Pages: 2

Brand: Electrolux Pages: 2

584097 (WFWROFOOOC)

Brand: Electrolux Pages: 2

Brand: Electrolux Pages: 2

Brand: Electrolux Pages: 2

Brand: Electrolux Pages: 2

Brand: Electrolux Pages: 62

Thermetic 9CHG583284

Brand: Electrolux Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands