Alliance Laundry Systems BD3LLFGS401UW01 Troubleshooting Manual Download Page 22

Page: 22 / 71

513447

Dryer Troubleshooting

9. Igniter Glows But Burner Does Not Ignite – Gas Dryer Models

Gas dryer models: Igniter glows but
burner does not ignite.

Did sensor

fail in closed

position?

Replace sensor.

Yes

Is secondary

coil or holding

coil open?

Is gas supply

insufficient?

Check gas
supply and
pressure. Make
sure gas shut-
off valve is
turned on.

Yes

DRY1852S

Replace gas
valve (in
warranty) or
replace coils
(out of
warranty). Refer
to

Test

Procedures

section.

Yes

Are igniter

and bracket

improperly

installed on
burner tube

assembly?

Loosen screw and
properly position
igniter and bracket
on burner tube
assembly.

Is sensor

improperly

installed on

burner

housing?

Loosen screw
and properly
position the
sensor on the
burner housing.

Yes

Summary of Contents for BD3LLFGS401UW01








































































Search results

Summary of Contents for BD3LLFGS401UW01

Reviews:

Related manuals for BD3LLFGS401UW01

Brands by name

Popular brands

Alliance Laundry Systems BD3LLFGS401UW01, Troubleshooting Manual

Search results

Summary of Contents for BD3LLFGS401UW01

Reviews:

Related manuals for BD3LLFGS401UW01

Brands by name

Popular brands