Airwell RWV01 Operation & Installation Manual Download Page 34 | Manualshive

Page: 34 / 52

background image

33

Operation

(6) The mode of indoor units can be inquired /changed by the
advanced setting function after the wired controller is powered
on, Only valid for part of models.
(7) Set as follows (Only valid for part of models):
Press Set key and Up key for 5s to enter the advanced setting
state, with the function A in temp. display area displayed
statically. Press Fan key to switch to function B. The function

code 01 displayed in the clock display area will flash. The
specific information in the timing display area is statically

displayed, it can be changed in the range of 00-03 by Up/

Down key. At this time press Set key to confirm, and the
function code 01 in clock display area stays static, the specific
information in the timing display area flashes, meaning it can

be changed currently. Press Up/Down key to change the

content and Set key to confirm.

(8) If the mode is changed from more to less, the current mode
will not be in the mode of the present circulation. It will be the
fan mode after turn on.

«
...
32
33
34
35
36
...
»

Summary of Contents for RWV01





















































Reviews:

No comments

Related manuals for RWV01

Brand: ABB Pages: 52

Brand: GARDTEC Pages: 48

Brand: FAAC Pages: 64

Brand: Yardney Pages: 8

Brand: Salda Pages: 20

Brand: Lakeshore Pages: 186

Brand: Mamas & Papas Pages: 44

Brand: Mamas & Papas Pages: 8

Brand: Omegalink Pages: 2

Brand: MamaLove Pages: 9

Brand: Saab Pages: 4

Brand: Ultratec Pages: 33

Brand: Watlow Pages: 59

Tekmar WiFi Snow Melting Control 670

Brand: Watts Pages: 48

Brand: TCi Pages: 9

FX-COMM4NDER MFX3203

Brand: Magicfx Pages: 16

Centronic SunWindControl SWC245-II

Brand: Becker Pages: 52

Brand: Fluidmaster Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands