Airwell RWV01 Operation & Installation Manual Download Page 33 | Manualshive

Page: 33 / 52

background image

32

Operation

(1) In off and non screen saving state, press Mode key for 5s,
it will display 8 segment on the top-left corner of current mode
circulation, default value being 0. Press Up/Down key to shift

between 0, 1, 2, 3, then press Set key to confirm value. It will

follow the altered mode circulation after turning on the unit
again.
Corresponding mode of different value.
0-------------[Intelligent] [Heating] [Dry] [Cooling] [Fan]
1-------------[Heating] [Dry] [Cooling] [Fan]
2-------------[Dry] [Cooling] [Fan]
3-------------[Heating] [Dry] [Cooling] [Fan]
(2) If modes are reduced and the mode that is set before
turning off is not in the newly set mode circulation, the initial
mode is fan.
(3) The intersection of mode circulation set by wired controller
and indoor unit is valid.

(4) Fresh Air unit can execute mode setting, it will execute

the intersection with three modes of Fresh Air unit (cooling/
heating/fan mode)

(5) This setting is ground floor setting and will be memorized

whether non-volatile memory invalid or valid.

Mode Setting (Only valid for part of models)

«
...
31
32
33
34
35
...
»

Summary of Contents for RWV01





















































Reviews:

No comments

Related manuals for RWV01

Brand: Eaton Pages: 16

Brand: Ebyte Pages: 35

Brand: K&K Pages: 10

Brand: SMC Networks Pages: 10

Entelli-Switch 250

Brand: GE Pages: 32

Brand: WANDERS Pages: 16

Brand: National Instruments Pages: 14

Brand: Sturtevant Richmont Pages: 73

Brand: KWC Pages: 8

Arteor 5 742 74

Brand: LEGRAND Pages: 2

Brand: Danfoss Pages: 16

Brand: LOVATO ELECTRIC Pages: 18

Brand: D+H Pages: 4

Brand: Samson Pages: 96

SecPath NSQ1FAB08D0

Brand: H3C Pages: 3

Brand: VADDIO Pages: 16

Brand: Dukane Pages: 30

Brand: Polaroid Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands