Airwell RWV01 Operation & Installation Manual Download Page 31 | Manualshive

Page: 31 / 52

Airwell RWV01 Operation & Installation Manual Download Page 31

30

Operation

(2) The circulation of the wind deflector:
four-way cassette deflectors controlled together→four-way
cassette deflector 1→four-way cassette deflector 2→four-way
cassette deflector 3→four-way cassette deflector 4→four-way
cassette deflectors controlled together.
(3) If it’s not the first time to enter it, press Set key, the wind
deflector set last time will flash. Meanwhile the angle of this
deflector set last time will be displayed statically, and the
number of the wind deflectors next to Up/Down swing will be

statically displayed.

(4) Press Set key to choose the wind deflector, and the
selected one will flash. At this time press Up/Down key to
adjust the angle of the wind deflector. The wind deflector will
keep flashing when adjusting. After finishing adjusting for
5s, the wind deflector will be displayed statically, meaning
existing the angle adjustment. At this time press Up/Down

key to adjust the temp.. Pressing mode key or Fan key during

the adjustment will exist the adjustment of four-way cassette
function. The position and angle of the wind deflector will be

set the same as last time. If no pressing Up/Down key for 5s

after Set key pressed, the selected wind deflector will stop
flashing and go back to the previous state.

«
...
29
30
31
32
33
...
»

Summary of Contents for RWV01





















































Reviews:

No comments