Airwell RWV01 Operation & Installation Manual Download Page 28 | Manualshive

Page: 28 / 52

background image

27

Operation

When filter cleaning icon

is displayed, the icon will display

in function sequence. If filter cleaning icon is flashing, press

key to clear it.

Filter Cleaning

(1) Press

key to enter function setting, then press

to choose energy saving, press

key again to confirm the

operation and display energy saving icon

. If energy

saving function has been set, the above operation will cancel
it.
(2)The energy saving default parameter are 23°C (74°F) (the
lowest temp. limit of cooling and dry mode) and 26°C (78°F)
(the highest temp. limit of heating mode). The temp. adjusting
range is 23°C-30°C (74°F-80°F) in cooling and dry mode, the
temp. adjusting range is 16°C-26°C (60°F-78°F) in heating
mode. If energy saving function is set, the indoor units will run
at the default temperature.
Note: Fresh Air unit has no energy saving function.

Energy Saving

«
...
26
27
28
29
30
...
»

Summary of Contents for RWV01





















































Reviews:

No comments

Related manuals for RWV01

Brand: Zolix Instruments Pages: 22

Brand: Lawler Pages: 2

Harmony Controller 2000

Brand: A10 Pages: 27

Brand: Jafar Pages: 10

Brand: Baby Trend Pages: 8

Brand: Baby Trend Pages: 19

Brand: Baby Trend Pages: 5

Brand: Baby Trend Pages: 4

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

coviva Smartbox TKP100A

Brand: hager Pages: 4

Brand: Vag Pages: 12

Brand: Hanwell Pages: 34

Brand: HANSONG Pages: 11

Brand: Datapath Pages: 12

Brand: Hansen Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands