AirLive PoE-2600HD User Manual Download Page 27

Page: 27 / 112

2. Preparation

AirLive PoE-2600HD/

WN-2600HD User’s Manual

2.2 UPnP of Windows® XP, Vista or 7

UPnP™ is short for Universal Plug and Play, which is a networking architecture that

provides compatibility among networking equipment, software, and peripherals. This

device is an UPnP enabled device. If the operating system, Windows XP, Vista or 7, of

your PC is UPnP enabled, the Network Camera will be very easy to be found.

Please refer to Appendix J to enable UPnP settings only if your operating system of PC is

running Windows XP.

Note

: Windows 2000 does not support UPnP feature.

To discover your device, go to your Desktop and click

My Network Places

Click the targeted

Device

. Then Internet Explorer will connect to this Network Camera

automatically.

2.3 Install the Device behind a NAT Router

Once installed, the device is accessible on your LAN. To access the device from the

Internet you must configure your broadband router to allow incoming data traffic to the

device. If the device is installed on the LAN with a router, then it may get a dynamic IP

address from the DHCP server. However, if the device wants to be accessed from the

WAN, its IP address needs to be setup as fixed IP, also the port forwarding or Virtual

Server function of router needs to be setup.

Summary of Contents for PoE-2600HD

















































































































Search results

Summary of Contents for PoE-2600HD

Reviews:

Related manuals for PoE-2600HD

Brands by name

Popular brands

AirLive PoE-2600HD, User Manual

Search results

Summary of Contents for PoE-2600HD

Reviews:

Related manuals for PoE-2600HD

Brands by name

Popular brands