AirLive PoE-2600HD User Manual Download Page 11

Page: 11 / 112

1. Introduction

AirLive PoE-2600HD/

WN-2600HD User’s Manual

Rear View

Audio Output Jack

Audio-out Jack allows this device to output audio or alerting sound.

DC Power Jack

The input power is 12VDC.

Note

that supply the power to the Camera with the power

adapter included in package. Otherwise, the improper power adapter may damage the unit

and result in danger.

Antenna Connector

User can attach the included antenna to this connector (SMA type) or use another

high-gain antenna to get higher performance.

Factory Default Reset

This button is hidden in the pinhole. This button is used to restore the all factory default

settings. Sometimes restarting the camera will make the system back to a normal state. If

the system still got problems after restart, user can restore the factory default settings and

install it again. To restore the device, please follow the steps below:

Summary of Contents for PoE-2600HD

















































































































Search results

Summary of Contents for PoE-2600HD

Reviews:

Related manuals for PoE-2600HD

Brands by name

Popular brands

AirLive PoE-2600HD, User Manual

Search results

Summary of Contents for PoE-2600HD

Reviews:

Related manuals for PoE-2600HD

Brands by name

Popular brands