AirLive POE-100CAMV2 User Manual Download

Page: 97 / 138

AirLive

POE100CAMv2

User’s

Manual

1: PT Speed:

You may select the drop list to change

speed of camera movement.

2: PT control:

PT interface consist of a control icon

which can change view angle of your camera to 4

directions manually.

3: - (Zoom out)

：

to get PT camera zoom out.

4: + (Zoom in)

：

to get PT camera zoom in.

5: AutoPan:

to get PT camera auto panning.

6: Stop:

to stop PT camera’s auto-action.

7: Preset Point:

by this drop list, you could select

preset point (Preset point is configured in Admin

program).

7.5.6 System

Setting

Relay Setting/Cancel Alarm

【

Step1

】

Click “Relay Setting” button

【

Step2

】

Select the “Relay Location” to remote control

Digital Output (light, for example, via Internet) to on or

off. Control facility via “Relay Setting” may involve

electronic danger, please consult your system integrator

and get their professional support.

【

Note

】

“Relay Setting” button use the same button of Cancel Alarm, the text varies according to alarm

status.

3 4

Summary of Contents for POE-100CAMV2











































































































































Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands

AirLive POE-100CAMV2, User Manual

Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands