AirLive POE-100CAMV2 User Manual Download

Page: 31 / 138

AirLive

POE

‐

100CAMv2

User’s

Manual

Mobile

View

RTSP (If RTSP mode is ON)

RTSP port:

Specify the transmission port number of RTSP streaming video. Default value is 8554.

RTP (If RTSP mode is ON)

Unicast streaming:

Unicast streaming Video/Audio port range:

Specify the transmission port range of RTP streaming video. RTP

will select a port randomly from the range.

Multicast streaming:

Multicast address:

Specify the multicast server address.

Video / Audio Port:

Specify the transmission port number of the video data. It is initially set to 10000 and 11000.

Specify an even number from 1024 to 65534.

Time-To-Live:

Set the maximum TTL that multicast can pass through.

Image Size:

The Image size of Mobile view is fixed at 176x120.

Frame rate

：

Set the frame rate of the MPEG4 image. Selectable values are 5, 10, 15, 20 fps. The unit “fps”

stands for “frames sent per second”.

Quality

Fixed Bit rate

：

Set the bit rate of MPEG4 image transmission for a line. Selectable values are 64, 32, and

16kbps.

Summary of Contents for POE-100CAMV2











































































































































Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands

AirLive POE-100CAMV2, User Manual

Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands