AirLive POE-100CAMV2 User Manual Download

Page: 71 / 138

AirLive

POE100CAMv2

User’s

Manual

User Belongs

【

Step3

】

Designating a User to a Group

Select the “User Belongs” tab to designate a user

to a group.

Select the group name and move it between

“Selected group” and “Unselected group”. Click

“OK” to continue.

After setting both general information and user

belongs, click “Create” to save the setting.

User Setting (Modify)

【

Step1

】

Select User Setting

Select User icon in the right, the User Table

display in the E-Map Interface area, when select

any user icon from the User Table, the User

Setting Button will display in the

Menu Bar

accordingly. Then click the Edit User button in the

Menu Bar.

【

Step2

】

Modifying user Information

You may change the information by modifying the

general information or user belongs of that user.

Summary of Contents for POE-100CAMV2











































































































































Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands

AirLive POE-100CAMV2, User Manual

Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands