AirLive POE-100CAMV2 User Manual Download

Page: 82 / 138

AirLive

POE100CAMv2

User’s

Manual

【

Step1

】

Select the Image icon

of a

LanCam in the System Setup area, and click

Image Setting button

from the Menu Bar

to bring up the Image setting window.

【

Step2

】

Click “Create” to save the setting.

Set Orientation

Click on the right of Image Rotation drop list to

support different camera mounting methods.

Here are “Normal” and “Inverted” for your option.

【

Note

】

(1) Monitor program requires restarting to

activate the new setting.

(2) This configuration requires 20 sec at least to

reconnect camera.

Schedule Recording

【

Step1

】

Select the Image icon and click Image

Setting button

to bring up the Image setting

window.

【

Step2

】

Select “Recording Type”

Check the Schedule in Recording Type first, and

you will find that the Schedule Setting button is

enabled.

Summary of Contents for POE-100CAMV2











































































































































Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands

AirLive POE-100CAMV2, User Manual

Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands