AirLive POE-100CAMV2 User Manual Download

Page: 94 / 138

AirLive

POE100CAMv2

User’s

Manual

7.5.4Camera Selection

Select the camera location by clicking the drop list.

Display Selection

Display Selection (Video of Single Camera)

Select camera button in Display Selection.

【

Note

】

The number of camera varies according to the

registration status.

Display Selection (Split Screen of Multiple Cameras)

Select split screen in Display Selection, the video display area

will change the video accordingly.

【

Note

】

Double click the selected screen in Split screen, the split screen will change to single display

mode.

Pause the live video

Click the pause button

, the live video will be paused and the button change to play button

, for user to

click to get the live video back.

7.5.5 Local Video Setting

Local Record

Live video could be manually recorded in the local computer by clicking the Local Record button, so that user

could record live video easily and save in any local computer.

Start Local Record

【

Step1

】

Select a camera from display area by a red

frame.

【

Step2

】

Click “Local Record” button to start the

recording.

Summary of Contents for POE-100CAMV2











































































































































Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands

AirLive POE-100CAMV2, User Manual

Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands