AirLive POE-100CAMV2 User Manual Download

Page: 87 / 138

AirLive

POE100CAMv2

User’s

Manual

Motion Detection

【

Step1

】

Select the Image icon of a

LanCam/Video Server in the System Setup area,

and click Motion Detection button

from

the Menu Bar to bring up the Motion Detection

window.

【

Step2

】

Set Detection Area: A red square

follows mouse movement, click to place the red

square to the area of motion detection or click to

deselect a specified area. Any motion within the

detected area should over the threshold of

sensitivity to trigger a motion detection alarm.

【

Step3

】

Sensitivity and Frequency setting.

Sensitivity refers to the pixels of image changes,

and Frequency refers to the No of frame

mapping.

【

Note

】

The size of red frame is configurable in Motion Detection Granularity, details please refer to Section

D.3.8. Motion Rectangle.

Different camera may have different interface for motion detection adjustment. Some may require you to

install Active-X components.

Summary of Contents for POE-100CAMV2











































































































































Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands

AirLive POE-100CAMV2, User Manual

Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands