AirLive POE-100CAMV2 User Manual Download

Page: 29 / 138

AirLive

POE

‐

100CAMv2

User’s

Manual

6.1.4 MPEG4

Computer View

RTSP (If RTSP mode is ON)

RTSP port:

Specify the transmission port number of RTSP streaming video. Default value is 554.

Viewer authentication:

If the viewer authentication is ON, users viewing through RTSP will be requested to

key-in username and password.

RTP (If RTSP mode is ON)

Unicast streaming:

Unicast streaming Video/Audio port range:

Specify the transmission port range of RTP streaming video. RTP

will select a port randomly from the range.

Multicast streaming:

Multicast address:

Specify the multicast server address.

Video / Audio Port:

Specify the transmission port number of the video data. Specify an even number from 1024

to 65534.

Time-To-Live:

Set the maximum TTL that multicast can pass through.

Summary of Contents for POE-100CAMV2











































































































































Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands

AirLive POE-100CAMV2, User Manual

Search results

Summary of Contents for POE-100CAMV2

Reviews:

Related manuals for POE-100CAMV2

Brands by name

Popular brands